Iso 2248 drop test pdf
Rating: 4.9 / 5 (4421 votes)
Downloads: 35608
CLICK HERE TO DOWNLOAD
this part of iso 7965 specifies a method of vertical impact testing on a filled paper sack by dropping. on either the edge or rim. isoe) descriptors : packing, transport complete- and filled packages, tests, impact drop tests. the atmospheric conditions, the height of drop and the attitude of the package are predetermined. iso 2248- 1: 1972 packaging complete, filled transport packages. en 22248 vertical impact test by dropping. however, since both the silicon wafers and the packaging systems exhibit certain degrees of rotational symmetry, several orientations were not tested. the drop height shall be measured from the top of the timber. 3 sacks and bags ( see 2. 1 scope and field of application. the international agreement concerning the international carriage of dangerous goods by road ( adr) as well as iso 2248 describe the char- acteristics of impact targets for drop tests of dangerous goods packagings. all protocols type of shock test drop test type of equipment free- fall drop tester in compliance with the apparatus section of. 1 this test method covers procedures for the drop testing of loaded boxes, cylindrical containers, and bags and sacks by the free- fall method. com is the first single pan- european information point for standards and legislation in europe. 1 lift the test package and hold it in the predetermined attitude ( see annex) at a height within ± 2% of the predetermined drop height as defined by the distance between the lowest point on the package at the time of release and the nearest point on the impact surface ( 4. 2 impact at any of the points 1, 2, 3, etc. 3 of is0 2206) the centre of gravity of the sack shall be vertically above the face, end or side involved in the impact. txt) or read online for free. 2 release the test package from its predetermined. principle: raising of the test package above a rigid plane surface and releasing it to strike this surface ( the impact surface) after a free fall. iso 2233 - packaging - complete, filled transport packages and unit loads - conditioning for testing published by iso on ma this international standard specifies a method for the conditioning of complete, filled, transport packages and unit loads. genorma is your website for european and international standards, harmonised iso 2248 drop test pdf standards and compliance issues, launched in collaboration with bds and other national standardization bodies. outcome of a drop test. , parallél to the axis of the cylinder. test objective: the primary objective of the test according to iso 2248 is to examine the effects of a vertical impact on a package. pdf), text file (. a rectangular box has a total of six unique faces, twelve edges and eight corners. 2) the difference in behaviour of a sack, for example, suspended from the top or supported below in an and drop, could be significant. packaging - complete, filled transport packages - vertical impact test by dropping ( iso 2248: ss- en 22248. drop test the attitude of the drop is defined in is) 2248: 1985 [ 3] as the orientation of the package on impact. 2 for containers not exceeding 110 lb ( 50 kg), this test method fulfills the requirements of iso standards 2206: 19: 1985. pdf - free download as pdf file (. 8 conditioning apparatus— adequate facilities shall be provided for. iso 2248: 1985 packaging - - complete, filled transport packages - - vertical impact test by dropping. an annex gives the predetermined attitude of the test package. these iso standards may describe procedures. in such instances, the method of holding the package before dropping shall be described in the test report. according to these regulations, the iso 2248 drop test pdf impact target' s surface needs to be unyielding, under testing. 7 for very large containers, it may be necessary to use a hoist, sling, and tripping devices, or a solenoid- operated drop test mechanism and suspension devices, such as those described in appendix x1. price based on 3 pages. vertical impact test by dropping emballages - d expkdition complets et pleins - essai de choc vertical par chute libre second editionudc 621. the test can be used as an independent test to measure impact resistance, or it can be integrated into a series of tests to evaluate the overall performance of a package in a distribution system. 2 for containers not exceeding 110 lb ( 50 kg), this test method fulþlls the requirements of iso standards 2206: 19: 1985. it may be performed either as a single test to investigate the effects of vertical impact or as part of a sequence of tests designed to measure the ability of a sack to withstand a distribution system that. caution— these iso standards may describe procedures that do not. 2) the difference in behaviour of a sack, for example, suspended from the top or supported below in an end drop, could be significant. these iso standards may describe procedures that do not meet. 1 this is a preview of iso 2248: 1985. chamber and control apparatus complying with the apparatus section of iso 2233 or astm d 4332. packaging — complete, filled transport packages — part 1: vertical impact test by dropping. 93 standard confirmed. 3 impact on any of the lines 12, 34, etc. principle: raising of the test package above a rigid plane surface and releasing it to strike this surface ( the impact surface ) after a free fall. iso 2248 or astm d 5276 additional required equipment hazard block: the block shall be made of hardwood or metal.