Iso 13337 pdf
Rating: 4.6 / 5 (9218 votes)
Downloads: 40157
CLICK HERE TO DOWNLOAD
each member body interested in a subject for which a technical. iso 13337: ( e) pdf disclaimer. a for slotted spring- type straight pins with a nominal diameter d. international standards are drafted in accordance with the rules given in the iso/ iec directives, part 2. iso 13337: 1997 spring- type straight pins - slotted, light duty. 1 scope this international standard specifies the characteristics of slotted spring- type straight pins, made of steel or of austenitic or martensitic stainless steel, light duty, with nominal diameter, d 1, from 2 mm to 50 mm inclusive. purdue mep truly partnered with jaeger- unitek to provide a complete and comprehensive iso 50001 certification and training package. spring- type straight pins, light type. metric series- isoformerly din 7346) metric pins 8mm and smaller diameter double chamfer is standard ( see top chart) metric pins over 8mm in diameter single chamfer is standard ( see bottom iso 13337 pdf chart) * * in individual cases, it is important to check whether these shear forces can be taken into account depending on the structural properties. when those changes occur, the rto or iso may need to change the data being. iso 13337 ~ dinhv bn 878 slotted spring pins light duty steel hardenedhv black • ~ uni 6874 • ~ csn 022156 article# d1 d1 min. pdf for information only. pins 13 through 50 m nominal diameter also available. 197355 q brl ca canada 0. iso shall not be held responsible for identifying any or all such patent rights. note the nominal diameters have been chosen in such a way that pins can. risk management — vocabulary management du risque — vocabulaire international standard iso 31073 first editionreference number iso 31073: ( e) iso 13337 was prepared by technical committee iso/ tc 2, fasteners, subcommittee sc 10, product standards for fasteners. also known as roll pins. the work of preparing international standards is normally carried out through iso technical committees. iso 13337: specifies the characteristics of slotted spring- type straight pins, made of steel or of austenitic or martensitic stainless steel, light duty, with nominal diameter from 2 mm to 50 mm inclusive. iso and not the mmus. goupilles cylindriques creuses, dites goupilles élastiques — série mince. s l, 3 1, 9 0, 2 0,. measure length from end to end. iso 13337 slotted spring pins light duty both ends are chamfered on pins less than 10 mm in diameter; only one end may be chamfered on 10 mm and larger diameter pins. non- governmental, in liaison with iso, also take part in the work. scope: this international standard specifies the characteristics of slotted spring- type straight pins, made of steel or of austenitic or martensitic stainless steel, light duty, with nominal diameter, d1, from 2 mm to 50 mm inclusive. therefore, any associated burden is counted as a burden on rtos and isos. ics code ( pins, nails) : 21. iso 377: ( e) foreword iso ( the international organization for standardization) is a worldwide federation of national standards bodies ( iso member bodies). while the ongoing delivery of data under ferc– 921 is continuous and routine, each rto or iso makes sporadic changes to its individual market with commission approval. click here to purchase the full version from the ansi store. this is a preview of iso 13337: . stift elastic, crestat. iso 13337 is similar to din 7346. double shear is not specified for 300 series stainless steel. this pdf file may contain embedded typefaces. full description. 6484 q aud at austria 0. this second edition cancels and replaces the first edition ( iso 13337: 1997), which has been technically revised. mounting hole nominal diameter tolerance zone is hi 2. 077658 d ats be belgium 0. 02649 d bef br brazil 0. this international standard specifies the characteristics of slotted spring- type straight pins, made of steel or of austenitic or martensitic stainless steel, light duty with nominal diameter, d 1, from 2 mm to 50 mm inclusive. din 7346 - dowel pins, light version current norm: din en iso 13337 equivalent norms: iso 8752; csn 022156; uni 6874;. double shear is only applicable to carbon and 420 stainless steel. spring pin iso 13337 – 6 × 30 – st example 2 a martensitic stainless steel ( c), non- interlocking slotted spring- type straight pin ( n), light duty, with nominal diameter d 1 = 6 mm and nominal length l = 30 mm is designated as follows: spring pin iso 13337 – 6 × 30 – n – c ´ ˆ˜ ¯ ˘ ˙ ˙ ˙ ¨ ˚ ˘ ¸ ¸ ¨. iso 3269, fasteners — acceptance inspection iso 4042, fasteners — electroplated coatings iso 6507- 1, metallic materials — vickers hardness test — part 1: test method iso 8749, pins and grooved pins — shear test 3 dimensions see figure 1 and table 1. spring- type straight pins — slotted, light duty. country/ union rate ind cur code ; au australia 0. through the diligent efforts and guidance from purdue mep, jaeger- unitek was able to fully secure iso 13337 pdf a state- funded grant to help cover almost all of the funding to cover all of the activities. © vogelsang fastener solutions, inc. iso collaborates closely with the international electrotechnical commission ( iec) on all matters of electrotechnical standardization.